2024 Haybuster® Tub Grinders H-1150 w/ Grapple

Information

2024 Haybuster® Tub Grinders H-1150 w/ Grapple

Bales go in. Loose hay comes out.

Do it all with the 1150 Tub Grinder from Haybuster.

Grinding Hay: big round & square bales, loose hay

Grinding Crop Residues: straw, stover, and other types

Grinding Grain: corn, sorghum, and all cereal grains

Commercial Grinding Applications

Features may include:

Rotary Self-Cleaning Screen

The enclosed engine compartment and rotary self-cleaning screen protects the engine from dirt and debris buildup. An enclosed engine also reduces the noise level. The 1150 with grapple loader gives you easy access to the engine with a 3-door entry on either side, plus a front door for access to the radiator.

C15 Caterpillar Electronic Diesel Engine

Powered by a 540 HP (403 kw) C15 Caterpillar Electronic diesel engine with state-of-the-art electronic fuel injection system, fuel consumption is decreased and ground hay is produced at a rate that will make you money on every job. It’s strong enough to chew through those tough, wet bales, and it has all the features you’ve come to expect from Caterpillar, including reliability, cold weather starting, unsurpassed product support, and proven resale value.

KPTO Fluid Coupler

The KPTO fluid coupler transmits power with up to 98% efficiency and eliminates the mechanical clutch. It’s goof proof. It can engage or disengage at full engine RPM without damage and requires minimal maintenance.

50 Degree Oscillating Stacking Conveyor

The 30 in. wide x 26 ft. long stacking conveyor piles hay to over 18 feet in height. The conveyor can oscillate left to right up to 50 degrees, which means you can not only make the pile tall, you can make it wide as well.

50” Big Bite Hammermill

The Big Bite hammermill is located at the rear of the tub frame, reducing the length of the belly conveyor, improving the belly conveyor service accessibility, and moving the dust away from the operator. The hammermill is also dynamically balanced to give you smoother operation, longer life, and less maintenance.

Photos

Highlights

  • Linden, Alberta
  • 2024
  • Haybuster®
  • Tub Grinders H-1150 w/ Grapple
  • C15
  • Diesel
  • Available
  • Tub: 1 ft (3.35 m) | 36 in (91.4 cm) | 30 in. (76.2 cm) | Frame: 34” +/- 1/2”
  • Loading: 9 ft 6 in (2.89 m) | Max. Conveyor Discharge: 18 ft 3 in (5.56 m)

Specifications

  • 2024
  • Haybuster®
  • Tub Grinders
  • H-1150 w/ Grapple
  • Tub
  • C15
  • CATERPILLAR
  • In-line
  • 6
  • 4 | 6.5 in (165 mm)
  • 475 HP (354 kw) or 540 HP (403 kw)
  • 5.4 in (137 mm)
  • 983 cu. in. (14.6 L)
  • Turbocharged and air to air aftercooling
  • 16.25 : 1
  • Oil to air, thermostatic controlled electric fan | Oil to Air, radiator mounted
  • Truck Horsepower: 300 HP (223.7 kw)
  • Electronic Unit Injector
  • Diesel
  • Direct from Fluid Coupling | Hydraulic, Top driven
  • Recommended Rear Axle: Air ride with dump valve (to lower loading height)
  • Engine Block Heater: 120V / 2000 watt
  • Screen Area: 2,781 sq. in. (7,063.75 sq. cm.)
  • Gear type, 2 section, output is 25 & 15 gpm @ 2100 psi., engine mounted
  • Type: Rubber Belt with 1-1/2 in (38.1 mm) Cleats | Type: Rubber Belt with 3/4 in (19.05 mm) cleats | Tub Floor Thickness: 1/4 in (6.35 mm) | Tub Wall Thickness: 12 gage (2.66 mm) | Tub Diameter at Base: 9 ft (2.74 m) | Screens: 1/8 in (3.18 mm), 3/16 in (4.76 mm), or 1/4 in (6.35 mm) thick and various hole sizes from 1/8 in (3.18 mm) to 8 in (203.2 mm) | Bearings: 4 in (101.6 mm), Pillow Block Bearings | Mill Shaft: 4-1/2 in (114.3 mm), Stress Proof Steel | Mill Plates: 1/2" (1.27 cm) thick X 16" (40.64 cm) dia. | Hammer Rods: 1-1/4 in (31.75 mm) dia., Case Hardened | Hammers: 1/2” (1.27 cm) AR-Hardened Steel , Swing | Feed Opening: 25 in x 52 in (63.5 cm x 133 cm) | Diameter, Hammers Extended: 26" (66.04 cm) | Conveyor Articulation: 2) 2 in x 8 in (5.08 x 20.3 cm) | Conveyor Fold: 2) 3 in x 30 in (7.62 x 76.2 cm) Hydraulic Cylinder | Conveyor Lift: 2) 3 in x 36 in ( 7.62 x 91.44 cm) Hydraulic Cylinders | Rotation: 270 degree | Wide Reach Grapple: 8' 4" (2.54 m) | Tub Tilt: 3 in x 30 in (7.62 x 76.2 cm) Hydraulic Cylinder
  • 10 ft (3.048 m)
  • 11 ft 6 in (3.51 m)
  • 31 ft (9.448 m)
  • Boom: 29 ft. (8.85 m) | 50" (127 cm) | 26 ft. (7.92 m)
  • Loading: 9 ft 6 in (2.89 m) | Max. Conveyor Discharge: 18 ft 3 in (5.56 m)
  • Tub: 1 ft (3.35 m) | 36 in (91.4 cm) | 30 in. (76.2 cm) | Frame: 34” +/- 1/2”
  • 50 in. (127 cm)
  • 9.2 gal. (34.8 L)
  • Lube Oil System (refill): 10 gal (38 L)
  • Mill Feeding: Mill Grate | Control Valves: Electric/Hydraulic, 4 valves - 1) 4 spool, 2) single spool, and 1 proportioning | Drain Type Fluid Coupling | TRANSFLUID | Rotation (from flywheel end): Counter-clockwise | Radiator: Staggered Core with 7 fins per inch
  • Total: 32,350 lbs. (14,704.5 kg)
  • 88
  • Frame: Steel